Beginner's Plumbing: The Essentials for Installing a Bathtub
Beginner's Plumbing: The Essentials for Installing a Bathtub
Blog Article
Just about everyone maintains their unique conception involving How to Install a Bathtub Yourself.
Installing a bathtub isn't exactly rocket science, however it does need solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably hard task. If the old tub is easily available, the project can relocate immediately; if you have to open up a wall surface to eliminate the old bathtub as well as position the brand-new bathtub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will require a helper to leave the old tub and embeded in the brand-new one. Make certain you have certified yourself for the task and are comfortable trying it. Rather than working with a specialist to take control of a halfway-completed project, it is much better to consider utilizing one prior to you start. Opportunities are you may need a professional plumber to make tube connections.
This article will certainly aid you mount a brand-new tub in your shower room if you have actually currently gotten a brand-new tub and also don't need to alter the arrangement of your previous water supply pipes.
Your devices as well as product checklist must comprise the following:
Getting ready for the Installment
First of all, the sustaining frame provided with the bath ought to be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you use all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its last position.
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, activate the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the restricted access that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have actually been eliminated, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any old securing compound.
Before going on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Making use of the two wooden boards under its feet, position the bathtub in the required position. The wood boards are valuable in equally spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 tiny points.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the tub until the level reads degree.
To mount faucets, fit all-time low of the outermost flexible tap adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and inspect all joints and new pipework for leakages and also tighten them if essential. Fill the tub and likewise inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the maker's user's manual. Tiling as well as sealing around the tub ought to wait until the bath tub has actually been utilized a minimum of once as this will resolve it right into its final placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin making certain that the washing machines are in area in between the tap and the sink. Secure the faucet in place with the manufacturer given backnut. As soon as the tap is firmly in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap connectors. The former type ought to be linked to the faucet finishes first, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to fracture a stiff seal, triggering the water to penetrate the wall between the bath and also the tiling, resulting in issues with wetness and also feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components and fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to enable the activity experienced when the tub remains in usage. The sealant can fracture fairly very early if you do not consider this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles utilizing waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that piece on A Step-by-Step Guide to Installing a Bathtub while browsing on the web. Liked our blog posting? Please share it. Help somebody else find it. We appreciate reading our article about How to Install a Bathtub.
Burst pipe? Phone! Report this page